Chargers

FMA CellPro 4S A123-compatible Charger
Advanced Lithium Charger with Full-Power Balancing Technology

Safe and E-Z, "No-hassle" Charging of ED-Nano (A123) Batteries from 1S (3.3V) to 4S (13.2V) in minutes at 4 Amps.

• Cells are individually balanced-while-charging
• E-Z, Fully automatic "no-brainer" operation!
• "Fuel Gauge" technology estimates remaining charge in a partially-discharged battery -- use as a battery checker!
• Real-time readout of individual cell voltages
• Displays "mAH added" when charged, useful for estimating in-flight power consumption!

No Node/Balance Extension 12" Extension (+$9.95) 36" Extension (+$14.95)

Quantity   

Charges and cycles LiPo and A123 cells, NiCd/MH cells and Lead-Acid Gell Cells -- in other words, just about any battery!

Capable of up to 10 amps (80 watts total) charging current.

Using the TP 610C charger to cycle your battery packs will improve their performance. The TP-610C charger’s built-in balancer will extend the life of your lithium packs!

* Max Charge Rate: 10A
* LiPo and A123 Cells: 1-6
* NiCd and NiMH Cells: 1-14
* PB Batteries: 6-12V


Comes with BL-2 balance adapter for TP and other LiPo.

No JR Balance Adapter Add TP-610C to JR Balance Adapter for ED-Nano 2S1P Batteries (+10)

Quantity   

• High frequency switch mode circuitry achieves high efficiency, small size, cool operating temperature and light weight.
• Reverse polarity protection both at input and output.
• Low-voltage detection circuit automatically preconditions a deeply discharged pack with a 30mA wake up charge.
• LEDs indicate charging modes and alarms.
• Constant Voltage - Constant Current (CVCC) method optimally charges 1 to 3 cell Li-Po batteries.
• Constant Current - Peak Detect optimally charges 1 to 8 cell NiCd / NiMH
• Programmable charge current: 300mA / 600mA / 1200mA / 2000mA
• Comes with JST 'BEC' connector.

The LN-5014 safely charges and cycles all Lithium, NiCd, NiMH and Lead-Acid battery packs.

• Backlit digital LCD screen displays battery type, charge/discharge mode, mAh, voltage, charging/discharging time.
• LCD screen also shows error messages for out-of-range input voltage, incorrect connection or reversed polarity, poor battery condition and internal errors.
• EZ-to-use 4-button control panel and totally straightforward menus
• Compact, simple to transport to the flying field or track.

Balance-Charge ED-Nano 2S packs with JR Node/Balance Connectors on FMA CellPro 4S and CellPro 10S chargers.
Quantity   

Safe and E-Z, "No-hassle" Charging of ED-Nano (A123) Batteries from 1S (3.3V) to 10S (33.0V) in minutes with adjustable charge current up to 10 Amps.

The CellPro 10S is the next level up from the CellPro 4S for those who want higher charging current (faster charge) with Heavy-Duty Batteries. It has all the features of its more economical CellPro 4S, with these additional features:

• Up to 10A Max Charge Current
• Continuous Power 300W (estimate)
• Displays Individual Cell Internal Resistance to 0.1 mohm Resolution (Battery Quality Indicator, a feature exclusive to the Cellpro 10s charger)
• Charges Lithium Polymer or A123 Cells (variable charge rates for both LiPo and A123 cells). Charges 1 Pack of 1s-10s or 2 Packs of 1s-5s Simultaneously
• Includes Start/Stop Button
• Backlit Liquid Crystal Display
• Supports 2-way P.C. Interface
• Drive the Charger from the P.C.
• Access Advanced Features from the P.C. (Setup Custom Presets, Adjust Speaker Volume, LCD Contrast, and More)
• Internet Upgradability (IU) Feature -- No need to send the charger to the factory for firmware upgrades again. Do it over the internet.

The Cellpro 10s charger may be used to charge any brand of Lithium pack using either the Cellpro adapters or pigtails. The charger includes two 5s output connectors and includes two simple 5s-to-4s adapters. This enables automatic support for any current Cellpro 2s-4s battery sold in the past. These extra accessories also enable you to connect any of the existing Cellpro 4s adapters for other brand batteries with the Cellpro 10s charger.

Using the Cellpro 10s Charge Control Software, the charger can be set to work with virtually any good, regulated power supply, even if the power supply is not designed for high power. By entering current capability; e.g., 1-25A, the charger will automatically adjust the maximum charge current to protect the programmed power supply. There is also a simple procedure that can be performed at the field to reset the input power supply to the factory default (25A) if a PC is not available. You might need to do this, if for example, you use a small AC power supply at home, but you want full charge current from your car battery at the field. This powerful feature allows you to decide how much money to spend on your power supply.

FMA’s Cellpro Node Connector is a key part of the system. It enables the charger to monitor individual cells and independently charge each cell to its optimum level.
 

Want a lower-cost charger alternative to a new, full-blown ED-Nano(A123)-compatible charger?
Adapt your existing NiCd ("Non-Pulsing") Charger to safely charge ED-Nano(A123) batteries without balancing.

• Balancing is preferable, but ED-Nano (A123) batteries may be charged up to 95% capacity on the 'Dapter-123 without balancing.
• E-Z, Fully automatic "no-brainer" plug-and-play operation!
• Charge up to 8 Amps, depending on your NiCd Charger
• Tested OK with
  • Multiplex LN5014
  • ElectriFly Triton
  • Schulze isl 8-936
  • Graupner Ultra Duo +25, +30
  • Astro 110D, 112D, 110 Deluxe

Balance ED-Nano 2S packs with JR Node/Balance Connectors on the Thunder Power TP-610C charger.
Quantity   

Balance ED-Nano 2S packs with JR Node/Balance Connectors on ALL Thunder Power and Thunder Power-compatible chargers.
Quantity